STEINEL RS PRO P1 flat indoor LED ceiling light without sensor, 8.2 W, 922 lm, 3000 K, IP54, white — 069704
Estimated sourcing to our Riga store: ~2 weeks.
Delivery to your address is counted from dispatch; for products on order, add it to the sourcing time. The carrier time is shown with the delivery method at checkout.
Quantities above available stock require sourcing of the remaining units. Check the information in your cart.
For collection, wait for confirmation that your order is ready.
- Indoor lighting
- Outdoor lighting
- Technical lighting
- LED bulbs
- LED strips and profiles
- LED power supplies
- Motion sensors and dusk switches
- Motion sensors
- Other
- Sale
Your shopping cart is empty!
Item specifics
- Light source type Integrated LED
- Replaceable light source No — LED is not user-replaceable
- Voltage 220–240 V AC
- Housing colour White
- Housing material Plastic
- Diffuser material Opal plastic
- Dimensions (L×W×H) 272 × 272 × 64 mm; Ø272 mm
- Mounting type Surface mounting on wall or ceiling
- IP rating IP54
- IK rating IK03
- Protection class (electrical) Class II — double insulation
- Operating temperature (Ta) −10…+40 °C
- Control method External on/off switch; can be wired to a compatible sensor version
- Soft light start Yes — soft light start
- Driver included Yes — power supply built into the luminaire
- Replaceable driver No
- Weight 355 g
- Warranty 5-year manufacturer warranty, subject to STEINEL terms
- Wattage 8.2 W
- Luminous flux 922 lm
- Luminous efficacy (lm/W) 112 lm/W
- Colour temperature (CCT) 3000 K
- Light colour Warm white
- Colour rendering index (CRI/Ra) Ra 82
- Colour consistency (SDCM) SDCM 3
- Mains frequency 50–60 Hz
- Dimmable No — not suitable for an external dimmer
- Energy class D — label for the built-in light source LS-0099
- Energy consumption (kWh/1000 h) 9 kWh/1000 h — light-source energy label
- Rated Lifetime (hours) IEC 62717: L70 100 000 h, L80 73 000 h; IES TM-21: L70/L80 >60 000 h
- Photobiological risk group RG1
- SKU 069704
- EAN 4007841069704
Product Description
STEINEL RS PRO P1 flat is a white indoor LED ceiling light without sensor for corridors, stairwells and indoor circulation areas. Its integrated LED delivers 922 lm at 8.2 W, with a fixed 3000 K warm-white light colour. Article 069704; EAN 4007841069704.
Control without a built-in sensor
This article has no motion sensor. Use an external switch or suitable external controller. It can also be wired to the switched circuit of a compatible RS PRO P1 sensor version, subject to the wiring diagram and load limits. Soft light start is provided, but the luminaire is not designed for an external dimmer. 3000 K and 4000 K are separate fixed-colour articles, not selectable settings on this unit.
Light quality and service life
922 lm is the complete luminaire’s luminous flux; 112 lm/W is its efficacy. CRI / Ra 82 describes colour rendering. SDCM 3 indicates initial light-colour consistency. LED cooling uses the passive Passive Thermo Control system.
Manufacturer lifetime figures: IEC 62717 L70 — 100,000 h; L80 — 73,000 h; IES TM-21 L70 and L80 — more than 60,000 h. L70 and L80 indicate retention of 70% and 80% of initial light output. These figures are not warranty periods.
The built-in LS-0099 light source carries energy class D and a label value of 9 kWh/1000 h; EPREL reference 882499. The energy label applies to the light source. The LED is included and is not a user-replaceable bulb.
Installation and package contents
Surface mounting on a wall or ceiling. Dimensions Ø272 × 64 mm follow the current article-specific data sheet and drawing; the older flat dimensions in the shared installation manual differ. This luminaire is intended for indoor use. The manual does not permit ceiling installation with a surface-mounted supply cable; plan a rear cable entry.
IP54 provides protection against harmful dust ingress and splashing water; bathroom placement must comply with applicable installation requirements. IK03 describes impact resistance. Class II means double insulation. Ambient operating range: −10…+40°C.
Included: one LED luminaire and three mounting spacers. The LED and driver are built in; no separate bulb is needed. This P1 version is not a battery-backed emergency luminaire.
Maximum stated inrush current is 13 A. The data sheet gives the following luminaire counts per circuit breaker: B10 — 54, B16 — 87, C10 — 90, C16 — 145. These are supply-circuit figures, not sensor-controlled group sizes. Cable capacity, total load and the wiring diagram also apply.
5-year manufacturer warranty, subject to STEINEL terms. Mains connection must be carried out by a qualified electrician. Manufacturer: STEINEL GmbH, Dieselstraße 80–84, 33442 Herzebrock-Clarholz, Germany; product@steinel.de.
The gallery contains manufacturer product photos, detail views and application illustrations. Other lights shown in series photographs are not included with this article.
Other versions in this family
- RS PRO P1 flat S, 4000 K, with sensor — 069674
- RS PRO P1 flat S, 3000 K, with sensor — 069681
- RS PRO P1 flat, 4000 K, without sensor — 069698
Manufacturer documents and video
- Data sheet (PDF) (EN)
- Operating and installation manual (PDF, multilingual)
- Wiring diagrams (PDF)
- Dimension drawing (PDF)
- Photometric data for lighting calculations (LDT)
- Tender specification (DOCX) (EN)
- EU declaration of conformity (PDF)
- Packaging conformity document (PDF)
- Built-in light source energy label (PDF)
- Manufacturer series brochure (PDF)
- Manufacturer warranty terms (PDF, German)
- Mounting drilling template (PDF; print at actual size)
- Manufacturer series video
- STEINEL product page
